When something goes wrong with the wiring in a Kuna home, the question is usually the same: how fast can somebody get there, and what is it going to cost. We handle electrical repair and installation throughout Kuna and Ada County, from a breaker that will not stay on to a full panel replacement to a dedicated circuit for a new appliance. You call, describe what you are seeing, and get a price on the phone before anything is scheduled. We are available every day from 8:00 AM to 9:30 PM.
Kuna is a city where single-family homes make up most of the housing stock, and the electrical calls that come out of a place like this reflect that: panels sized for a lighter load than what the house now draws, outlets that need GFCI protection added, ceiling fans going in where a light fixture used to be, and generator hookups before another winter outage makes the need obvious. We handle all of it. Local coverage. Safe wiring. Costs explained before we start.
Apartments and condos in Kuna carry their own set of electrical considerations. The panel is often tucked into a hallway closet, a utility room, or a storage area rather than a garage or basement, and the space around it can be tight. That does not change the work, but it does change how the visit goes.
In a multi-unit building, some circuits feed only the individual unit and some feed shared areas. Lighting in a stairwell, exterior outlets on a balcony, or wiring for a shared laundry room may sit on a different meter or a different panel entirely. Before we schedule work on a shared circuit, the right person to talk to is the property manager or building owner, because access and billing for that work run through them rather than through the tenant.
We protect your floors and finishes while we work, which matters in a unit where the flooring runs right up to the panel door and there is no utility room to absorb the mess a job can make.
Older homes sometimes have outlets that test as ungrounded, or a grounding system that was added after the original wiring and was not done completely. A grounding and bonding correction is not always a full rewire. Sometimes it is a matter of adding a ground wire to a circuit that was wired before grounding was required, or correcting a bonding connection at the panel that was missed during a previous repair. We check what is actually there before recommending what needs to change.
A Level 2 charger runs on a 240-volt dedicated circuit, and the first thing to settle is whether the panel has the capacity to add one. A load calculation tells us what the panel is already carrying and whether there is room for the new breaker. If the panel is close to its limit, the charger circuit and a panel upgrade go together. The installation covers the circuit, the outlet or hardwired connection, and any panel work needed before the breaker is added.
A panel where half the breakers are labeled "misc" or not labeled at all is a practical problem. It slows down every repair call, and it makes it harder to shut down the right circuit safely before any work begins. We trace and label circuits so the panel reflects what is actually connected to each breaker. It is a straightforward job that makes every future electrical visit faster and safer.
Doorbell wiring, data drops, and low-voltage rough-in for security cameras or smart home devices all require a clean installation to work reliably. The wiring needs to be run correctly the first time, especially in walls that are already finished. We handle the rough-in and the connections so the devices function as intended without creating a wiring problem in the process.
For a landlord or property manager, the electrical call usually starts with a tenant report: an outlet that stopped working, a breaker that keeps tripping, or a light fixture that has not functioned since the last turnover. The booking goes through the property owner or manager, and so does the invoice. The tenant provides access.
Before the visit is scheduled, it helps to know whether the tenant will be home, whether there are any access restrictions, and whether the panel is inside the unit or in a common area. If the panel is in a shared space, we need access confirmed in advance. A property owner who wants a written record of what was found and what was done can ask for that on the call when the job is scoped.
Panel and wiring work finished to code is the standard on every job, and that matters for a rental property where the work may be reviewed during a future inspection or sale. Anything not covered here is on our services page for electrical work.
When a fault will not keep, the process is the same as any other call: describe what you are seeing, get a price, and find out what is open on the schedule. We take short-notice work when the calendar allows, and availability from 8:00 AM to 9:30 PM every day covers most of the windows that matter. A breaker that will not stay on, an outlet that is sparking, or a smell near the panel are all reasons to call without delay.
For a rental property with a tenant in place, the visit is scoped so the electrician knows in advance what circuits need to be de-energized and for how long. For a commercial property that has to stay open, we work through the scope on the call to identify what can be done without shutting the whole building down. Some work has to happen in phases. That conversation starts on the phone, not after the electrician is already there.
A figure before anything starts. Flexible timing. Safe wiring.
The price for any electrical job depends on what the job actually involves. A panel upgrade where the service entrance also needs updating costs more than one where the meter base is in good shape. A circuit run through a finished wall takes longer than one in an unfinished basement. What the fault turns out to be, what has to be opened up to reach it, and whether the existing panel can carry the change are the three things that most often move a quote.
We go through those variables on the call. You describe what you are seeing, we ask what we need to know about the panel and the property, and we give you a price that covers the scope as we understand it. If the visit turns up something that changes the scope, that gets explained before any additional work is approved.
What you will not get is a number after the fact for work that was always part of the job. The price is confirmed before we schedule, and what it covers is explained at the same time.
Sometimes, yes, and sometimes no. The answer depends on what was done and whether it can be brought into line with current standards without tearing out what is there.
Work that was done incorrectly but is otherwise intact can often be corrected: a wire connected to the wrong terminal, a circuit that was not protected by the right breaker type, a ground wire that was omitted. Those are repairs. Work that used the wrong wire gauge for the load, or that was run in a way that cannot be made safe without replacement, has to come out.
We tell the difference by looking at what is there, not by assuming the worst. The visit covers the affected circuit, the connections, and the panel feeding it. If the previous work is salvageable, we say so. If it is not, we explain why before anything is touched.
We service this area, and its neighborhoods each have their own wiring. Kuna is the focus of this page, and it is where most of the calls we take in this part of Ada County come from. We also cover Meridian, Nampa, Boise City, Garden City, and Eagle, along with the surrounding Ada County communities in between.
Coverage means the work is done here, not that we are passing through. A call from a Kuna address gets the same process as any other: scope the job on the phone, confirm the price, and schedule when it works.
Single-family homes in this part of Ada County tend to generate calls around panels that have run out of capacity, outlets that need GFCI protection added, and circuits that were not sized for the loads now running on them. Generator hookups and EV charger circuits are also common requests, particularly before winter. The pattern reflects the housing stock: homes with growing electrical demands and panels that were not always sized to match.
We are available every day from 8:00 AM to 9:30 PM, including weekends. Short-notice scheduling is available when the calendar allows.
Call (208) 795-9878, describe what you are dealing with, and we will tell you what is open.
Urgent faults are handled during those hours, and the scope and price are settled on the call before anything is dispatched.
Not necessarily. Many jobs only require the circuit involved to be de-energized, leaving the rest of the property running normally. Where the work touches the panel or the service entrance, a broader outage is usually required for part of the visit, and we will tell you what to expect when the job is scoped on the call.
We trace unlabeled circuits during the visit by testing each breaker against the outlets and fixtures it controls and labeling the panel as we go. It takes longer than working from an accurate directory, but it is a necessary step before any panel work or circuit addition, and it leaves the panel in a more useful state than we found it.
It helps to know roughly when the problem started, whether it affects one outlet or one room or the whole house, and whether anything happened just before it, like a tripped breaker or a power flicker. If the panel is accessible, knowing whether any breakers are in the off or middle position is useful. None of this needs to be exact. The call is where we work through the details together so the visit can be scoped correctly.
Yes.
Call (208) 795-9878 and describe what you are dealing with, and we will go through the scope with you on the phone and give you a price before anything is scheduled.
The price covers what the job involves, and you know what it is before we confirm a time.
A dead outlet, a ceiling fan that will not respond to the wall switch, a panel where half the breakers have no label, a doorbell that stopped working: none of these are too small to be worth a call. Smaller jobs are often what turns up the larger problem, and they are worth handling before they become one. We are available every day from 8:00 AM to 9:30 PM.
Call (208) 795-9878, describe what you are dealing with, and get a price before anything is scheduled.
Electrical work in the surrounding towns: Meridian, Boise City, Garden City, Eagle.
The calls we get from Kuna and Ada County cover the full range of residential and commercial electrical work, from a single tripped breaker to a complete panel replacement. The table below lays out what each service covers, who it fits best, and a practical note worth knowing before you call. Every job gets a price on the phone before anything is scheduled, and the scope is confirmed before work begins.
Call (208) 795-9878 to talk through what you are seeing.
| Service | What's Included | Common Situations | Good to Know |
|---|---|---|---|
| Ceiling Fan Installation | Fan and wiring installationSwitch and remote wiringExisting box assessmentDedicated circuit where needed | Rooms without existing fan wiring or where a light fixture is being replaced | A ceiling fan needs a rated junction box, not just a light fixture box. We check the box before the fan goes up. |
| Whole-Home Surge Protection | Panel-level surge device installationGrounding and bonding reviewProtection for appliances and electronicsCoordination with outlet-level strips | Homes with sensitive electronics, newer appliances, or frequent utility voltage events | Panel-level surge protection handles large spikes that outlet strips cannot absorb. Both layers together give the most complete coverage. |
| Electrical Panel & Service UpgradesMost Popular | 200-amp service upgradesLoad calculation and panel sizingMeter base and service entrance workSubpanel installation for outbuildings | Older homes adding large loads, EV chargers, or electric heating equipment | A load calculation confirms what the panel is actually carrying before any upgrade work is scoped, so the new panel is sized for current and future demand. |
Call (208) 795-9878 to describe what you are seeing, get a price on the call, and find out what the job involves before anything is scheduled.
(208) 795-9878